- Step by step xen server vdi build how to#
- Step by step xen server vdi build install#
- Step by step xen server vdi build mac#
For Ubuntu 12.04, the mirror I used was xe vm-start uuid= will power on the VM and it will launch. Within this URL, some of it will be repeated so remove the repeated part and run the ' xe vm-param-set. I copied this address in, and then ran xe vm-start uuid= receiving an error that the URL was incorrect.
Step by step xen server vdi build install#
Then instead of guessing what the install repository was, I searched through the repository until I found the folder marked xen with the file vmlinuz contained within. Personally, I found that by searching for mirrors on the internet for the specific flavour of OS, I was able to find the mirror. Xe vm-param-set uuid= other-config:install-repository= defines the install location for the net installer of the OS.
Step by step xen server vdi build mac#
Xe vif-create vm-uuid= network-uuid= mac=random device=0 creates a virtual network interface for the VM with a random MAC address. If you are using a different bridge or want to attach the VM to a different adapter, then you can define a different name in place (however you need to make sure you've created one first :P). Xe network-list bridge=xenbr0 -minimal outputs the UUID of the bridge xenbr0 which is the default bridge for a fresh install of XenServer. By executing the command xe vm-list you can see a list of VMs which are currently installed on the host, displaying UUIDs for each and their current state. This then outputs the UUID of the VM in the console. Sr-uuid= 'installs' a VM based off the template onto the machine, however no actual installation occurs at this point. Xe template-list outputs the list of templates accessible on the XenServer host. Xe sr-list outputs the list of storage repositories the storage repository 'local storage' of type 'ext' provided for me a location where I could store the disks of each VM respectively. Ubuntu 12.04 and 10.Whatever 32-bit Debian Squeeze and Wheezy 32-bit), and so you are able to launch a VM in exactly the same way using the following commands: It actually turns out that all 32-bit Linux Distributions are compatible out of the box with PV (as a general rule of thumb, anything old is compatible eg. The next hurdle I had to cross was running a VM in PV mode, as the tower unit I was using did not support HVM. iso again and reinstalling, I found that by executing xe template-list output a long list of useful templates. It turned out I must have had a corrupt install of XenServer, and after downloading the. Ok, so eventually I found the answer to the problem I was facing. Many thanks for your time, and apologies for my probably ignorance. XenServer Host Name: xenserver-hxcwfafr-OliCallaghanXen In order to help anyone who answers, I have included the details of my server below:
Step by step xen server vdi build how to#
I am very confused, as XenServer is quite overwhelming, but I am determined to understand how to create a VM directly from the command line. I attempted to do this via the command line again, but searched the internet, and couldn't find any information as to how I would do it? I assumed that this would have been because I had not set the template, and wondered whether I could do this by creating an NFS VHD Storage Device? If I execute the above command ( xe vm-install.), I receive the following output, if I substitute in either "Ubuntu 14.04 (64-bit)" for template name and "Ubuntu" as the label: Error: No templates matched I am familiar with Docker, so wondered whether the process of creating a VM template was similar to creating a container image? I hoped there would be a magical command such as xe template-new or something of the sort, but I couldn't find one. In addition to this, I have no templates set or created, and wondered as to how I would do this. I understand that in order to create a VM, you run this command changing the, and appropriately: xe vm-install template= new-name-label=Īgain, as I am quite new to XenServer, I am unsure as to even what these need to be changed to. I chose to do so as XenCenter doesn't run on it, and also, as my project requires me to run the whole system from the command-line, but after spending an extortionate amount of time searching the internet for answers as to how to create VMs, I seemed to stumble upon the same, uninformative scripts, one after the other. I have installed XenServer on an unused Tower unit, and currently SSH into it from my Mac. I have an issue in which I cannot understand how to create a XenServer Virtual Machine from the command-line.